Не отключайте рекламу на сайте - поможете проектуx86_64: LFD10-23.05 ; Roll24.02-24.04 ; LFU22 ; FAS ; Alt-lxde3-auc i686: DDR01-21.08 Русские PuppyLinux
0 Пользователей и 1 Гость просматривают эту тему.
#Special base config file used in Puppy Linux.# **********************************************************************# Module section -- this section is used to specify# which dynamically loadable modules to load.# **********************************************************************#Section "Module"# This loads the DBE extension module. Load "dbe" # Double buffer extension# This loads the miscellaneous extensions module, and disables# initialisation of the XFree86-DGA extension within that module. SubSection "extmod" Option "omit xfree86-dga" # don't initialise the DGA extension EndSubSection# This loads the font modules Load "type1" Load "freetype"# This loads the GLX module### Load "glx"# This loads xtrap extension, used by xrandr Load "xtrap" #Load "mk712.ko #Load "evdev"EndSection# **********************************************************************# Files section. This allows default font and rgb paths to be set# **********************************************************************Section "Files"# The location of the RGB database. Note, this is the name of the# file minus the extension (like ".txt" or ".db"). There is normally# no need to change the default. RgbPath "/usr/X11R7/lib/X11/rgb"# Multiple FontPath entries are allowed (which are concatenated together),# as well as specifying multiple comma-separated entries in one FontPath# command (or a combination of both methods) FontPath "/usr/X11R7/lib/X11/fonts/misc/" FontPath "/usr/X11R7/lib/X11/fonts/Type1/" FontPath "/usr/X11R7/lib/X11/fonts/TTF/"EndSection# **********************************************************************# Server flags section.# **********************************************************************Section "ServerFlags"# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence# (where n is 1 through 12). This allows clients to receive these key# events.# Option "DontVTSwitch"# Enables mode switching with xrandr# There is a report that this can cause Xorg not to work on some# video hardware, so default is commented-out...# but i want to use it in xorgwizard so leave on... Option "RandR" "on"EndSection#everything past here is auto-generated by Puppy's Xorg Wizard...Section "ServerLayout" Identifier "X.org Configured" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" #"CorePointer"# InputDevice "Keyboard0" "CoreKeyboard" InputDevice "touchscreen0" "CorePointer" #"SendCoreEvents" EndSection#Section "InputDevice"# Identifier "Keyboard0"# Driver "kbd"# Option "XkbRules" "xorg"# Option "XkbModel" "pc102"# Option "XkbLayout" "us" #xkeymap0#EndSectionSection "InputDevice" Identifier "Mouse0" Driver "void" #"mouse"# Option "Protocol" "IMPS/2" #mouse0protocol Option "Device" "/dev/mouse" #Option "Emulate3Buttons" #Option "Emulate3Timeout" "50"# Option "ZAxisMapping" "4 5" #scrollwheelEndSection#Section "InputDevice"# Identifier "Mouse0"# Driver "void"## Option "Protocol" "IMPS/2" #mouse0protocol# Option "Device" "/dev/mouse"## #Option "Emulate3Buttons"## #Option "Emulate3Timeout" "50"## Option "ZAxisMapping" "4 5" #scrollwheel#EndSectionSection "InputDevice" Identifier "touchscreen0" Driver "evtouch" #Driver "mk712_touchscreen" Option "DeviceName" "touchscreen" Option "Device" "/dev/input/event2" Option "SwapX" "false" ## default false Option "SwapY" "true" #Option "Rotate" "CW" ## CW or CCW Option "MinX" "152" Option "MinY" "224" Option "MaxX" "4031" Option "MaxY" "4001" Option "ReportingMode" "Raw" Option "SendCoreEvents" "On" Option "TapTimer" "10" # default 200ms Option "LongTouchTimer" "50" # default 400ms Option "Emulate3Buttons" "false" # default true Option "Emulate3Timeout" "5" # default 50ms Option "MoveLimit" "30" # default 30 pixels Option "maybetapped_action" "click" #"click" # default click Option "maybetapped_button" "1" # default 1 (left) Option "oneandhalftap_action" "click" Option "oneandhalftap_button" "3" #Option "tap_action" "click" #Option "tap_button" "2" Option "longtouch_action" "click" # default down Option "longtouch_button" "3" # default 1 (left) #Option "DebugLevel" "2" #Option "Calibrate" "1"EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" #HorizSync 31.5 #VertRefresh 60.0 #UseModes "Modes0" #monitor0usemodes #HorizSync 31.5 #VertRefresh 40-70 #HorizSync 30-95 #VertRefresh 50-180 ModeLine "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync #ModeLine "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync #ModeLine "640x480" 25.18 640 656 752 800 480 490 492 525 -hsync -vsync #ModeLine "800x600" 56.30 800 832 896 1048 600 601 604 631 +hsync +vsync #UseModes "Modes0" #monitor0usemodes EndSection Section "Modes" Identifier "Modes0" #modes0modeline0EndSectionSection "Device" ### Available Driver options are:- ### Values: <i>: integer, <f>: float, <bool>: "True"/"False", ### <string>: "String", <freq>: "<f> Hz/kHz/MHz" ### [arg]: arg optional #Option "pci_burst" # [<bool>] #Option "fifo_conservative" # [<bool>] #Option "fifo_moderate" # [<bool>] #Option "fifo_aggressive" # [<bool>] #Option "pci_retry" # [<bool>] #Option "NoAccel" # [<bool>] #Option "set_mclk" # <freq> #Option "show_cache" # [<bool>] #Option "HWCursor" # [<bool>] #Option "SWCursor" # [<bool>] #Option "ShadowFB" # [<bool>] #Option "Rotate" # [<str>] #Option "VideoKey" # <i> #Option "ByteSwap" # [<bool>] #Option "Interlaced" # [<bool>] #Option "UseBIOS" # [<bool>] #Option "ZoomOnLCD" # [<bool>] #Option "Dualhead" # [<bool>] #Option "AccelMethod" # <str> Identifier "Card0" Driver "siliconmotion" #card0driver VendorName "Silicon Motion, Inc." BoardName "SM712 LynxEM+" BusID "PCI:0:6:0"EndSectionSection "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" DefaultDepth 16 Subsection "Display" Depth 16 Modes "800x600" "640x480" EndSubsection Subsection "Display" Depth 24 Modes "800x600" "640x480" EndSubsectionEndSection#PuppyHardwareProfile=Silicon_Motion_SM712