Модель ZTE MF180. Модем активирован заранее на другом ПК. Поведение при включении, после иннициализации загорается красным цветом индикатор, через 10-15сек меняет цвет на зелёный (нашёл сеть). Спустя несколько минут снова красный. Дистр 1.30 определил его как
# dmesg
ocessor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2800.69 BogoMIPS (lpj=5601381)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00002040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: Intel(R) Pentium(R) M processor 1400MHz stepping 05
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
ACPI: setting ELCR to 0200 (from 0800)
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfc96e, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0880-08bf claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #02 (-#05) is hidden behind transparent bridge #01 (-#01) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
PCI: Bus #06 (-#09) is hidden behind transparent bridge #01 (-#01) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
libata version 2.20 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:00: iomem range 0x0-0x9fbff could not be reserved
pnp: 00:00: iomem range 0x9fc00-0x9ffff could not be reserved
pnp: 00:00: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:02: ioport range 0x800-0x805 has been reserved
pnp: 00:02: ioport range 0x808-0x80f has been reserved
pnp: 00:03: ioport range 0xf400-0xf4fe has been reserved
pnp: 00:03: ioport range 0x806-0x807 has been reserved
pnp: 00:03: ioport range 0x810-0x85f has been reserved
pnp: 00:03: ioport range 0x860-0x87f has been reserved
pnp: 00:03: ioport range 0x880-0x8bf has been reserved
pnp: 00:03: ioport range 0x8c0-0x8df has been reserved
pnp: 00:08: ioport range 0x900-0x97f has been reserved
pnp: 00:0d: ioport range 0x7b0-0x7bb has been reserved
pnp: 00:0d: ioport range 0x7c0-0x7df has been reserved
pnp: 00:0d: ioport range 0xbb0-0xbbb has been reserved
pnp: 00:0d: ioport range 0xbc0-0xbdf has been reserved
pnp: 00:0d: ioport range 0xfb0-0xfbb has been reserved
pnp: 00:0d: ioport range 0xfc0-0xfdf has been reserved
pnp: 00:0d: ioport range 0x13b0-0x13bb has been reserved
pnp: 00:0d: ioport range 0x13c0-0x13df has been reserved
Time: tsc clocksource has been installed.
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bus 2, cardbus bridge: 0000:01:01.0
IO window: 0000e000-0000e0ff
IO window: 0000e400-0000e4ff
PREFETCH window: 30000000-33ffffff
MEM window: 3c000000-3fffffff
PCI: Bus 6, cardbus bridge: 0000:01:01.1
IO window: 0000e800-0000e8ff
IO window: 00001000-000010ff
PREFETCH window: 34000000-37ffffff
MEM window: 40000000-43ffffff
PCI: Bridge: 0000:00:1e.0
IO window: e000-efff
MEM window: fc000000-fdffffff
PREFETCH window: 30000000-39ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:01:01.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:01:01.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt 0000:01:01.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/W].
io scheduler noop registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
intel_rng: FWH not detected
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
Switched to NOHz mode on CPU #0
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 13824K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: WDC WD2500BEVE-00A0HT0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: max request size: 512KiB
hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: PS/2 Mouse as /class/input/input1
input: AlpsPS/2 ALPS GlidePoint as /class/input/input2
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 204k freed
EXT3 FS on hda2, internal journal
Adding 1052248k swap on /dev/hda1. Priority:-1 extents:1 across:1052248k
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000bf80
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000bf40
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 11, io base 0x0000bf20
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 11, io mem 0xfaeffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 855 Chipset.
agpgart: Detected 892K stolen memory.
agpgart: AGP aperture is 128M @ 0xf0000000
snd: no version for "unregister_sound_special" found: kernel tainted.
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 54643 usecs
intel8x0: clocking to 48000
slamr: module license 'Smart Link Ltd.' taints kernel.
slamr: SmartLink AMRMO modem.
slamr: probe 8086:24c6 ICH4 card...
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.6 to 64
slamr: mc97 codec is CXT22
slamr: slamr0 is ICH4 card.
tg3.c:v3.75.2 (June 5, 2007)
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
eth0: Tigon3 [partno(BCM95705A50) rev 3001 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:0d:56:6e:0c:eb
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
Yenta: CardBus bridge found at 0000:01:01.0 [1028:0139]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:01:01.0, mfunc 0x012c1202, devctl 0x64
Yenta: ISA IRQ mask 0x04d8, PCI irq 11
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#01) from #01 to #05
pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff
cs: IO port probe 0xe000-0xefff: clean.
pcmcia: parent PCI bridge Memory window: 0xfc000000 - 0xfdffffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x39ffffff
Yenta: CardBus bridge found at 0000:01:01.1 [1028:0139]
Yenta: ISA IRQ mask 0x04d8, PCI irq 11
Socket status: 30000047
Yenta: Raising subordinate bus# of parent bus (#01) from #05 to #09
pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff
cs: IO port probe 0xe000-0xefff: clean.
pcmcia: parent PCI bridge Memory window: 0xfc000000 - 0xfdffffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x39ffffff
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
bcm43xx driver
ACPI: PCI Interrupt 0000:01:03.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
bcm43xx: Chip ID 0x4306, rev 0x3
bcm43xx: Number of cores: 5
bcm43xx: Core 0: ID 0x800, rev 0x4, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0x5, vendor 0x4243
bcm43xx: Core 2: ID 0x80d, rev 0x2, vendor 0x4243
bcm43xx: Core 3: ID 0x807, rev 0x2, vendor 0x4243
bcm43xx: Core 4: ID 0x804, rev 0x9, vendor 0x4243
bcm43xx: PHY connected
bcm43xx: Detected PHY: Analog: 2, Type 2, Revision 2
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
pcmcia: Detected deprecated PCMCIA ioctl usage from process: cardmgr.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x820-0x8ff: excluding 0x8e0-0x8e7
cs: IO port probe 0x820-0x8ff: excluding 0x8e0-0x8e7
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x100-0x3af: excluding 0x378-0x37f
cs: IO port probe 0x100-0x3af: excluding 0x378-0x37f
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
PM: Writing back config space on device 0000:01:00.0 at offset b (was 165d14e4, writing 865d1028)
PM: Writing back config space on device 0000:01:00.0 at offset 3 (was 0, writing 2008)
PM: Writing back config space on device 0000:01:00.0 at offset 2 (was 2000000, writing 2000001)
PM: Writing back config space on device 0000:01:00.0 at offset 1 (was 2b00000, writing 2b00106)
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PM: Writing back config space on device 0000:01:00.0 at offset b (was 165d14e4, writing 865d1028)
PM: Writing back config space on device 0000:01:00.0 at offset 3 (was 0, writing 2008)
PM: Writing back config space on device 0000:01:00.0 at offset 2 (was 2000000, writing 2000001)
PM: Writing back config space on device 0000:01:00.0 at offset 1 (was 2b00000, writing 2b00106)
PM: Writing back config space on device 0000:01:00.0 at offset b (was 165d14e4, writing 865d1028)
PM: Writing back config space on device 0000:01:00.0 at offset 3 (was 0, writing 2008)
PM: Writing back config space on device 0000:01:00.0 at offset 2 (was 2000000, writing 2000001)
PM: Writing back config space on device 0000:01:00.0 at offset 1 (was 2b00000, writing 2b00106)
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
usb 4-4: new high speed USB device using ehci_hcd and address 2
usb 4-4: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 0:0:0:0: Direct-Access Corsair Voyager Mini 0.00 PQ: 0 ANSI: 2
SCSI device sda: 31588352 512-byte hdwr sectors (16173 MB)
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 31588352 512-byte hdwr sectors (16173 MB)
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
usb-storage: device scan complete
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
usb 4-4: USB disconnect, address 2
#
И с подключённым модемом в режиме "сеть найдена"(см прилепленный файл). Вопрос. Можно ли его заставить работать на дистрибутиве 1.30?
Сайт
Скачать
Видео
Wiki
